- Home
- Equipment
Refine by
Sisgeo Environmental Equipment & Supplies
14 equipment items found
Manufactured by:Sisgeo S.r.l. based inMasate (MI), ITALY
Optical coordinometer is a device designed to detect the coordinates (X-Y) of the plumb line on a horizontal surface. The measuring principle is based on high-accuracy photecells able to detect the pendulum wire position: the coordinates are read with the IP67 dial gauge fixed on the coordinometer. The instrument can be also used on the TEL-310S telecordinometer measuring plate in the case that ...
Manufactured by:Sisgeo Asia Pacific Co., Ltd based in, THAILAND
In-Place Inclinometer (double wheel-carriage) is specifically designed to combine the benefits of automatic monitoring and the selective installation of probes at different depths. This configuration allows a cost effective solution in those cases where the critical depths are known. Consequently the probes may be concentrated only in some areas along the borehole profile. IPI probes are equipped ...
Manufactured by:Sisgeo Asia Pacific Co., Ltd based in, THAILAND
Vibrating wire strain gauges provide measurements of strain in steel or concrete structures. The measurements are used to calculate structural loads or stresses. Arc-weldable strain gauges are fixed to steel structures via weldable end-blocks. On concrete surfaces they can be installed by means of mounting blocks that include rebar-bolts. Embedment strain gauges are cast into concrete structures ...
Manufactured by:Sisgeo Asia Pacific Co., Ltd based in, THAILAND
The measurement of inclinations is essential for the control and security of the civil structures in elevation during the construction phase and in operation. MEMS tiltmeters monitor tilt changes in either one or two axial planes perpendicular to the surface of the base plate. MEMS analog tiltmeters are permanently installed to provide long term observation and are designed for manual readings or ...
Manufactured by:Sisgeo S.r.l. based inMasate (MI), ITALY
Vibrating wire piezometers are used to monitor pore-water pressure in soils. They are typically sealed in boreholes but can also be embedded in fills, or suspended in a well. Typical applications include evaluating slope stability, dewatering and drainage schemes, overpressure in silt and clay soils, permeability and hydraulic gradients in dams, and also ground water levels. They can also be used ...
Manufactured by:Sisgeo Asia Pacific Co., Ltd based in, THAILAND
TILLI is a portable tiltmeter composed by a rugged stainless steel frame with aluminium sensor housing containing a self-compensated MEMS accelerometer. The surfaces of the frame are machined to allow an accurate positioning of the tiltmeter during measurements. When in use, TILLI is placed on the tilt plate which is permanently installed on the structure surface. The bottom surface of the ...
Manufactured by:Sisgeo S.r.l. based inMasate (MI), ITALY
Multipoint vibrating wire piezometers, also called multilevel piezometers, provide measurements of pore-water pressure at different elevations in the same borehole. Isolation of the pore-water pressure at each elevation is achieved by the fully-grouted installation ...
Manufactured by:Sisgeo S.r.l. based inMasate (MI), ITALY
The H-Level is the automatic liquid level system for accurate long-term monitoring of differential settlements in buildings, tunnels, and other civil ...
Manufactured by:Sisgeo S.r.l. based inMasate (MI), ITALY
The multipoint settlement systems consist of a number of hydraulic settlement gauge connected by tubing to a reference tank located on higher, stable ...
Manufactured by:Sisgeo S.r.l. based inMasate (MI), ITALY
Sisgeo QJ tube is an alternative to the traditional inclinometer casings, mainly designed for earth-fill dam and deep boreholes applications. QJ tube offers consistent joint and deeper tube grooves. O-rings prevent ingress of grout or water. The fitted-at-factory casings and the alignment keys assure a perfect grooves continuity. QJ fast installation reduce costs and limit drilling rig ...
Manufactured by:Sisgeo S.r.l. based inMasate (MI), ITALY
Inclinometers are special grooved tubes, generally installed in a borehole, used in conjunction with inclinometer system to monitor horizontal soil movements. Flush-coupled inclinometer casing is a special ABS grooved tube, machined at the end to have a self-aligning junction. It is produced from high-quality virgin ABS plastic. During manufacturing particular attention is paid to minimise the ...
Manufactured by:Sisgeo S.r.l. based inMasate (MI), ITALY
Hydraulic pressure cells are designed to measure stress in mass concrete or placed at the interface between the structure and the wall of excavation. The pressure pad consists of two steel plates welded together around their periphery and spaced apart by a narrow cavity saturated under vacuum with de-aired oil which guarantee maximum rigidity. A length of high-pressure rilsan tubing connects the ...
Manufactured by:Sisgeo Asia Pacific Co., Ltd based in, THAILAND
Vibrating wire piezometers are used to monitor pore-water pressure in soils. They are typically sealed in boreholes but can also be embedded in fills, or suspended in a well. Typical applications include evaluating slope stability, dewatering and drainage schemes, overpressure in silt and clay soils, permeability and hydraulic gradients in dams, and also ground water levels. They can also be used ...
Manufactured by:Sisgeo Asia Pacific Co., Ltd based in, THAILAND
B.R.A.IN (Borehole Readout Array for INclinometers) system is mainly composed by MEMS inclinometer probe, bluetooth reel with control cable and B.R.A.IN APP compatible with Android and iOS mobile operative systems. The electronis readout is integrated in the reel and the BLE (Bluetooth Low Energy) wireless protocol permits a fast and safe communication with the management device, with a very low ...