MCE products for research use only. We do not sell to patients.

CY5

MCE China：CY5

Brand：MedChemExpress (MCE)

Cat. No.HY-D0821

CAS：146368-11-8

Synonyms：Sulfo-Cyanine5

Purity：98.99%

Storage：4°C, protect from light *In solvent : -80°C, 2 years; -20°C, 1 year (protect from light)

Shipping：Room temperature in continental US; may vary elsewhere.

Description：CY5 is a CY dye. CY, short for Cyanine, is a compound consisting of two nitrogen atoms connected by an odd number of methyl units. Cyanine compounds have the characteristics of long wavelength, adjustable absorption and emission, high extinction coefficient, good water solubility and relatively simple synthesis. CY dyes are of en used for the labeling of proteins, antibodies and small molecular compounds. For the labeling of protein antibodies, the combination can be completed through a simple mixing reaction. Below, we introduce the labeling method of protein antibody labeling, which has certain reference significance.

In Vitro：Protocol1.Protein Preparetion1) In order to obtain the best labeling effect, please prepare the protein (antibody) concentration as 2 mg/mL.2) The pH value of protein solution shall be 8.5±0.5. If the pH is lower than 8.0, 1 M sodium bicarbonate shall be used for adjustment.3) If the protein concentration is lower than 2 mg/mL, the labeling efficiency will be greatly reduced. In order to obtain the best labeling efficiency, it is recommended that the final protein concentration range is 2-10 mg/mL.4) The protein must be in the buffer without primary amine (such as Tris or glycine) and ammonium ion, otherwise the labeling efficiency will be affected.2.Dye Preparation (Example for CY3-NHS ester) Add anhydrous DMSO into the vial of CY3-NHS ester to make a 10 mM stock solution. Mix well by pipetting or vortex. Before use, it must be activated with condensation solution (500 μg/mL) (HY-D0178) before subsequent labeling experiments can be performed. 3.Calculation of dye dosageThe amount of CY3-NHS ester required for reaction depends on the amount of protein to be labeled, and the optimal molar ratio of CY3-NHS ester to protein is about 10.Example: assuming the required marker protein is 500 μL 2 mg/mL IgG (MW=150,000), use 100 μL DMSO dissolve 1 mg CY3-NHS ester, the required CY3-NHS ester volume is 5.05 μL, and the detailed calculation process is as follows:1) mmol (IgG) = mg/mL (IgG) ×mL (IgG) / MW (IgG) =2 mg/mL × 0.5 mL / 150,000 mg/mmol= 6.7×10-6 mmol2) mmol (CY3-NHS ester) = mmol (IgG) × 10 = 6.7×10-6 mmol×10 = 6.7 × 10-5 mmol3) μL (CY3-NHS ester) = mmol (CY3-NHS ester) ×MW (CY3-NHS ester) / mg/μL (CY3-NHS ester) = 6.7 ×10-5 mmol ×753.88 mg/mmol / 0.01 mg/μL = 5.05 μL (CY3-NHS ester) 4.Run conjugation reaction1) A good volume of freshly prepared 10 mg/mL CY3-NHS ester is slowly added to 0.5 mL protein sampleIn solution, gently shake to mix, then centrifuge briefly to collect the sample at the bottom of the reaction tube. Don'tmix well to prevent protein samples from denaturation and inactivation.2) The reaction tubules were placed in a dark place and incubated gently at room temperature for 60 minutes at intervals.For 10-15 minutes, gently reverse the reaction tubules several times to fully mix the two reactants and raise the bar efficiency.5.Purify the conjugationThe following protocol is an example of dye-protein conjugate purification by using a SepHadex G-25 column.1) Prepare SepHadex G-25 column according to the manufacture instruction.2) Load the reaction mixture (From "Run conjugation reaction") to the top of the SepHadex G-25 column.3) Add PBS (pH 7.2-7.4) as soon as the sample runs just below the top resin surface.4) Add more PBS (pH 7.2-7.4) to the desired sample to complete the column purification. Combine the fractions that contain the desired dye-protein conjugate.

Emission (Em)：670

Excitation (Ex)：633

Hot selling product：I-BET151  | GNE-7915  | Fenofibrate  | 5-Aminolevulinic acid (hydrochloride)  | Gambogenic acid  | N-Formyl-Met-Leu-Phe  | Hyocholic Acid  | Pomalidomide  | Gelucire 44/14  | Vismodegib

Trending products：Recombinant Proteins  |  Bioactive Screening Libraries  |  Natural Products  |  Fluorescent Dye  |  PROTAC  |  Isotope-Labeled Compounds  |  Oligonucleotides

References：

[1]. Ptaszek M. Rational design of fluorophores for in vivo applications. Prog Mol Biol Transl Sci. 2013;113:59-108.  [Content Brief]

[2]. Shindy, H. A. (2017). Fundamentals in the chemistry of cyanine dyes: A review. Dyes and Pigments, 145, 505–513. doi:10.1016/j.dyepig.2017.06.029