- Home
- Companies
- Dwyer Instruments, LLC d/b/a DwyerOmega
- Products
- Omega - Model FMA-2600 Series - Mass ...
Omega - Model FMA-2600 Series -Mass Flow Controllers
The FMA-2600A Series mass and volumetric flow controllers use the principle of differential pressure within a laminar flow field to determine and control mass flow rate. A laminar flow element (LFE) inside the meter forces the gas into laminar (streamlined) flow. Inside this region, the Poiseuille equation dictates that the volumetric flow rate be linearly related to the pressure drop. A differential pressure sensor is used to measure the pressure drop along a fixed distance of the LFE. This, along with the viscosity of the gas, is used to accurately determine the volumetric flow rate. Separate absolute temperature and pressure sensors are incorporated and correct the volumetric flow rate to a set of standard conditions. This standardized flow rate is commonly called the mass flow rate and is reported in units such as standard cubic feet per minute (SCFM) or standard liters per minute (SLM).
- 20+ Gas Calibrations, Including: He, O2 , Neon, N2O, N2, Air, Argon, CO, CO2, Methane, Ethane, Propane, Butane, Acetylene, Ethylene, H2
- Pressure, Temperature, Volumetric & Mass Flow Simultaneously Displayed
- Easy Operator Push Button Interface
- NIST Traceability Standard
- Full Scale Ranges from 0.5 SCCM to 3000 LPM
- Response Time of 100 milliseconds Typical
- Turndown Ratio of 100:1 Typical
- Position Insensitive
- Accuracy of ±1% Full Scale
- RS232 Standard
- No Warm Up Time
The controller uses a true proportional valve coupled to the flow body to control flow using the integral PID loop controller. Standard units include a 0 to 5 V output (4 to 20 mA optional) and RS232 communications. The gas-select feature and the setpoints can be adjusted from the front keypad or via RS232 communications. Volumetric flow, mass flow, absolute pressure, and temperature can all be viewed or recorded through the RS232 connection. It is also possible to multi-drop up to 26 units on the same serial connection to a distance of 45 metres.
- Repeatability: ±0.2% FS
- Turndown Ratio: 100:1
- Control Response Time: 100 ms
- Input Control Signal: 0 to 5 Vdc, RS232
- Output Signal: 0 to 5 Vdc, RS232
- Optional Input/Outputs: 4 to 20 mA, 0 to 10 Vdc
- Operating Temperature: -10 to 50°C (14 to 122°F)
- Zero Shift: 0.02%/ATM FS/°C
- Span Shift: 0.02%/ATM FS/°C
- Humidity Range: 0 to 100% RH, non-condensing
- Excess Flow Rate: 2.4% FS
- Wetted Materials:
- Small Valve: 303 & 302 Stainless Steel, FKM, Heat Cured Silicone Rubber, Glass Reinforced Polyphenylene Sulfide, Heat Cured Epoxy, Aluminium, Gold, Brass, 430FR Stainless Steel, Silicon, Glass.
- Large Valve: 303 & 302 Stainless Steel, FKM, Heat Cured Silicone Rubber, Glass Reinforced Polyphenylene Sulfide, Heat Cured Epoxy, Aluminium, Gold, 416 Stainless Steel, Silicon, Glass.
- Maximum Pressure: Mass Flow Controllers: 145 psig
- To Use in Volumetric Mode: Near atmosphere, 15 psig recommended maximum. Volumetric flowmeters and controllers not certified for accuracy at mass flow rates above the rated flow range of the meter. They are designed for near atmospheric pressure conditions only. The recommended maximum operating pressure is 15 psig
- Minimum Differential Pressure Required:
- 5 SLM and under: 5 psid
- 10 to 250 SLM: 15 psid
- 500 SLM: 5 psid
- 1500 SLM: 10 psid
- Supply Current: 0.250 A for 20 SLM and under; 0.75 A for 50 SLM and above (typical)
- Supply Voltage: 12 to 30 Vdc for units 20 SLM and smaller; 24 to 30 Vdc for units 50 SLM and larger
- Electrical Connections: 8-pin circular mini DIN