AMS Water Monitoring Equipment
-
PremiumManufactured by AMS, Inc.based in USA
Prevent cross contamination with a cased access hole. The portable AMS Hollowstem auger kit provides the tools needed to reach a 6' depth. The augers cut a 3' diameter hole and have an ID of 1 1/8', making them suitable for soil, soil gas and groundwater sampling through a cased hole. A special Hollowstem soil probe, 7/8' OD by 24' long with slide hammer is included to allow collection of a soil ...
-
PremiumManufactured by AMS, Inc.based in USA
AMS 6-inches (152mm) Gas Vapor Implant Installation Kit are used for permanent soil gas monitoring, UST monitoring, groundwater sampling, air sparging, vapor extraction monitoring, and as a pressure measurement point in vacuum testing. This kit allows a user to obtain or collect a soil gas sample by positioning or placing a 6” implant in the subsurface, and subsequently withdrawal a sample ...
-
PremiumManufactured by AMS, Inc.based in USA
You asked for it and we listened. No more threaded connections! The New AMS 3-1/4” Hex Quick Pin Sampling Kit allows for collection of both disturbed & relatively undisturbed core samples down to a depth of 12ft. This kit features hardened steel male/female hex connections that accept standard 3/8” snapper pins or heat treated 3/8” U-clips. The simplicity of the snap pins is ...
-
PremiumManufactured by AMS, Inc.based in USA
The Deluxe AMS Fiberglass Auger Kit provides some protection against possible electric shock when working in areas where buried electric cables may be present. This kit features the trusted AMS Signature Series thread pattern, which takes 2-1/2 revolutions to connect & disconnect. The two-piece 36-inch Tile Probe (with rounded safety tip) has a detachable plastic handle & zinc plated ...
-
PremiumManufactured by AMS, Inc.based in USA
Install as permanent sample point, or leave in ground as a disposable point. AMS dedicated gas vapor tips are used for detecting hydrocarbon spills, underground storage tank and pipe leaks, landfill contamination and hazardous waste sites. Soil gas monitoring with the AMS dedicated gas vapor tip is easily accomplished using an available AMS gas vapor probe ...
-
PremiumManufactured by AMS, Inc.based in USA
AMS offers a variety of dredges designed for sampling sand and silt as well as most types of non-cohesive material. AMS sampling dredges are placed onto the bottom sediment, then closed and pulled up to retrieve a sample. Careful release of the sample distributes the sample approximately as it appeared on the bottom – making sediment profile description possible. The sample is not suitable ...
-
PremiumManufactured by AMS, Inc.based in USA
Easily collect sludge samples from the bottom of petroleum tanks with this unique & user friendly sampling kit. Based on the popular design of the ‘AMS Multi-Stage Sediment Sampling Kit’, the components in this kit are similar, only they are made from lightweight aluminum. This proves to be crucial, as often times tanks can be 50ft.+ in height; therefore keeping your sampler and ...
-
PremiumManufactured by AMS, Inc.based in USA
AMS Water Level Meters provide reliable and accurate measurements of groundwater levels. Water level readings are taken at the top of the casing with accuracy to within 1/100 of a foot (3mm). They utilize a durable polypropylene storage reel with a rugged solid aluminum frame. Their highly accurate Polyethylene-coated steel tape is available in either standard/English or metric unit increments. ...
-
PremiumManufactured by AMS, Inc.based in USA
Easily collect sediment or sludge with a technically enhanced core tip and cap. The AMS "valved core tip" fills the sampler without losing the sample upon retrieval. The sampler uses a disposable plastic soil catcher that fits on the end of a 2" x 12" plastic liner. The core tip allows the plastic soil core catcher and liner to fit snuggly over the lip of the core tip. Once the soil core catacher ...
-
PremiumManufactured by AMS, Inc.based in USA
Easily collect sediment or sludge with a technically enhanced core tip and cap. The AMS "valved core tip" fills the sampler without losing the sample upon retrieval. The sampler uses a disposable plastic soil catcher that fits on the end of a 3" x 12" plastic liner. The core tip allows the plastic soil core catcher and liner to fit snuggly over the lip of the core tip. Once the soil core catcher ...
-
PremiumManufactured by AMS, Inc.based in USA
Full Groundwater Pumping Automation for Pump Deployment, Retrieval and Operation up to 300 feet Deep. Management of dedicated pump installation and monitoring is enhanced with the patented AMS design. The automation of boom extension, rotation and elevation plus motor-driven spools for pump deployment/retrieval, make the 7000 series easy and convenient to ...
-
PremiumManufactured by AMS, Inc.based in USA
The AMS Fiberglass Auger Kit provides some protection against possible electric shock when working in areas where buried electric cables may be present. The one-piece 48-inch Fiberglass Tile Probe included in the kit is ideal for locating irrigation, power and water lines, and it should be used as a primary device to determine whether or not it is safe to use a hand auger at the sampling ...
-
PremiumManufactured by AMS, Inc.based in USA
Pask Permeameter Kit; The field saturated hydraulic conductivity (Kfs) or permeability of natural soil and built up beds of fill can be quickly and easily measured in place using the ETC Pask Constant Head Permeameter Kit manufactured by Dynamic Monitors, a business unit of Engineering Technologies Canada Ltd. ...
-
PremiumManufactured by AMS, Inc.based in USA
The AMS PowerProbe 9110-LAP is a portable direct push rig, designed for use in confined spaces or buildings where a vehicle-mounted probe cannot go. This model can be driven off any standard AMS PowerProbeª with an auxiliary hydraulic hook-up kit, or the optional AMS portable hydraulic power unit. The 9110-LAP comes standard with a 90 ft-lb hydraulic ...
-
PremiumManufactured by AMS, Inc.based in USA
Professional Series Multi-Stage Sediment/Sludge Sampler Kit! This sampling kit provides all of the components needed to collect sludge and sediment samples 3” in diameter & up to 24” in length. The 12" long (female/female threaded) base section and (1) extra 12” (male/female threaded) body section allows you to assemble a sampler that is 24” in length. This kit was ...
-
PremiumManufactured by AMS, Inc.based in USA
AMS Water Level Meters provide reliable and accurate measurements of groundwater levels. Water level readings are taken at the top of the casing with accuracy to within 1/100 of a foot (3mm). They utilize a durable polypropylene storage reel with a rugged solid aluminum frame. Their highly accurate Polyethylene-coated steel tape is available in either standard/English or metric unit increments. ...
-
PremiumManufactured by AMS, Inc.based in USA
This mini soil probe measures 1” – dia. X 14” length w/ 12” long sample slot and is constructed of thick (.109w) chromoly steel and has been nickel plated for corrosion resistance. The soil probe has a chamfered plug welded in at the top of the slot. The cross handle is powder coated chromoly and measures 1” –dia. X 10” long and has rubber grips for ...
-
PremiumManufactured by AMS, Inc.based in USA
The AMS 3500 is the smallest of the AMS well management systems. It was designed for users with a limited number of wells to monitor. This capable unit is available with manual or hydraulic systems. The automated, hydraulic-driven boom with double-spool system will handle sampling jobs up to 300 ft deep. The SK-3500 is built on a self-contained skid that can easily be slid into or out of a ...
-
PremiumManufactured by AMS, Inc.based in USA
AMS Water Level Meters provide reliable and accurate measurements of groundwater levels. Water level readings are taken at the top of the casing with accuracy to within 1/100 of a foot (3mm). They utilize a durable polypropylene storage reel with a rugged solid aluminum frame. Their highly accurate Polyethylene-coated steel tape is available in either standard/English or metric unit increments. ...
-
PremiumManufactured by AMS, Inc.based in USA
Easily sample most types of bottom surfaces. Constructed from stainless steel and powder-coated carbon steel for corrosion resistance. The top of the sampling chamber is screened to allow water flow during deployment and reduce the frontal shock wave that may displace sediment as the dredge contacts the sample surface. A two-way spring-loaded mechanism activates on contact with the bottom, no ...
Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you