Anyone and everyone who is responsible for operating and maintaining a swimming pool or spa has to test, monitor, and control complex, interdependent chemical factors that affect the quality of water bathers are immersed in. Additionally, aquatic facilities operators must be familiar with all laws, regulations, and guidelines governing what these parameters should be.
The natural gas industry has seen a significant increase in activity with the discovery of new shales located throughout the world. The development of advance drilling technologies allow for extraction of gases deeper in the earth, revolutionizing the industry while creating a new demand for air and water pollution control technologies.
The remediation division of Anguil Environmental Systems (formerly known as Global Technologies) is focused on treating emissions and water contaminants extracted from below the earths` surface. Formed shortly after the 1990 Clean Air Act targeted emissions associated with the extraction of polluted compounds from contaminated sites, Global subsurface remediation equipment has been successfully applied on contaminated sites in North and South America, Europe, Asia and Australia.
To produce efficiently several feed formulations starting from continuously changing raw materials and premixes, require flexible and accurate analytical and formulation technologies. BUCHI offers dedicated solutions for the entire value chain: from R&D and QC laboratories to the production lines.
Every beverage bottling facility requires a cost efficient, clean method for the disposition of out of date or out of spec products. Shred-Tech® has been providing solutions to suit this need for many years. All shapes and sizes of cans, plastic bottles and aseptic packaging have been processed using our systems.
Semiconductor manufacturing processes involve highly toxic substances and flammable gases. Our ChemLogic 96 Continuous and DOD64 FTIR Sequential gas analyzers are staples in this industry with over 1,000 machines operating every day worldwide. Our gas analyzers can be found in a few different places throughout a fabrication facility such as: In the Wafer Reactor, Wafer Dryer, Gas Cabinets, and during Chemical Vapor Deposition. Our units are designed with clean environments in mind. With a sample draw of 400 feet...
Polyurethane Foam requires toxic gases in it’s manufacturing process. The most common gases fall into the Diisocyanate family of gases. Toluene Diisocyanate (TDI) and Methylenediphenyl diisocyanate (MDI) have exposure limits set by the Occupational Safety and Health Administration (OSHA) to ensure employee protection in polyurethane facilities.
Controlling dialysate quality is critically important to hemodialysis patient health. Complications as minor as nausea and fatigue or as severe as metabolic acidosis and sepsis can result if dialysate composition is incorrect. All the factors that ultimately affect dialysate composition must therefore be carefully monitored and controlled: proper proportioning and mixing of concentrates with water; the quality of water mixed with concentrates to form dialysate; and the quality of water used in the reprocessing of...
Dairy industry faces the challenge of the disposal of many by-products from the production process, such as Whey, Hot Whey, Buttermilk and cheese processing wastewater.
Our cost-effective solutions allow taking advantage of all the by-products, which either are a cost or have low value, thanks to the generation of biogas.
The most common treatments are either Anaerobic treatment only with a medium-low biological plant, or a Dissolved Air Flotation followed by a high load biological plant.
The benefits are the...
Boilers and cooling towers share two major water related problems: deposits and corrosion. As steam is generated by a boiler or water evaporating from a cooling tower, dissolved minerals are left behind, increasing the concentration of these minerals. Additional minerals are introduced via the water added to makeup the water lost to steam/evaporation. Eventually, the minerals reach a level (or cycle) of concentration that will cause either loss of efficiency due to scale or damage from corrosion. This level can...
Contamination of circuit boards can bring about severe degradation of insulation resistance and dielectric strength. Cleanliness of completed circuit boards is, therefore, of vital interest. For those companies who have established circuit board cleaning procedures, the MIL Spec P-28809 has been used as a guideline for control. Now a simple `on line` test for the relative measurement of ionic contamination has been developed. This fast and economical method for testing circuit board cleanliness uses a Myron L...
Years ago, high purity water was used only in limited applications. Today, deionized (Dl) water has become an essential ingredient in hundreds of applications including: medical, laboratory, pharmaceutical, cosmetics, electronics manufacturing, food processing, plating, countless industrial processes, and even the final rinse at the local car wash.
Oxidation Reduction Potential or Redox is the activity or strength of oxidizers and reducers in relation to their concentration. Oxidizers accept electrons, reducers lose electrons. Examples of oxidizers are: chlorine, hydrogen peroxide, bromine, ozone, and chlorine dioxide. Examples of reducers are sodium sulfite, sodium bisulfate and hydrogen sulfide. Like acidity and alkalinity, the increase of one is at the expense of the other.
From cutting-edge MABR wastewater treatment to containerized desalination, Fluence delivers cost-effective and sustainable solutions for commercial customers worldwide. Fluence has more than 30 years of experience in the design, construction, and operation of water and wastewater treatment plants for commercial clients, including resorts, golf courses, commercial buildings, and campuses.
Fluence has decades of experience providing sustainable treatment solutions for power industry process water and effluent. Industrialization and population growth are spurring the demand for power around the world, putting pressure on fuel and water resources. At the same time, power producers face strict pollution and air-quality controls.
The OSEI Corporation manufactures a first response bioremediation product Oil Spill Eater II that has been used to clean up leaks around storage tanks from valve breaks, line breaks and small holes in tanks, as well as for tank sludge clean outs. OSE II has been cleaning up oil/hydrocarbon based spills including heavy oils, sludge, drilling mud, tailings as well as refined product since 1989.
Grinding-swarf from the metal processing industry may contain metal alloys, stainless-steel and high-alloyed steel, all of which are ideal input-materials VacuDry unit. The absence of oxygen in the VacuDry process prevents any changes in the chemical structure of the oil, emulsions or metals during the treatment. The output material can later be sold at high prices.
As is the case for many industrial manufacturing processes, emissions are best destroyed through the use of thermal and catalytic oxidation technologies. Volatile Organic Compounds (VOCs) and Hazardous Air Pollutants (HAPs) are destroyed through the use of high temperature combustion with direct heat recovery. The harmful air pollutants are converted to heat, water vapor and carbon dioxide, creating a destruction efficiency greater than 99%.