Only show results in Virginia? Ok

Flumes equipment for Water and Wastewater

  • Premium

    Eijkelkamp - Model 13.17.02 - Water discharge Measurements: RBC Flumes

    RBC flumes are used to measure the quantity of water that, for instance, flows through an irrigation channel. By comparison to known flumes, such as the WSC-and the Parshall flume, the RBC flume is the most accurate. The RBC flume has been specially designed for use in smaller water ways or earthen channels (irrigation channels, in- outlets, ...

    By Eijkelkamp Soil & Water based in Giesbeek, NETHERLANDS. from Water discharge Measurements: RBC Flumes Product line

  • Parshall Flumes

    With wide flow ranges, resistance to submersion, simple flow meter calibration, and self-cleaning design, Parshall flumes are the first choice of many engineers and end-users. Typical applications include: Sewage treatment plant influent and effluent, Industrial process discharge, Irrigation and agricultural runoff.

    By TRACOM Inc. based in Alpharetta, GEORGIA (US) (USA). from Parshall Flumes Product line

  • Plasti-Fab - H, HS and HL Flumes

    The H flume and related HS & HL flumes are gaining in popularity due to their ability to handle wide ranging flows that can vary by as much 100:1 or more from low to peak. Because of the unique throat, which resembles a weir in some respects, the H flumes provide excellent resolution at low flows and still have capacity to capture peak flow ...

    By Plasti-Fab, Inc. based in Tualatin, OREGON (USA). from H, HS and HL Flumes Product line

  • Model HS / H / HL - Flumes

    The Dust Bowl experienced by the United States during 1930’s saw the establishment of the Soil Conservation Service (SCS) on April 27, 1935. The SCS was established as a permanent agency the US Department of Agriculture with a mission to conserve the nation’s soil and water resources.

    By Openchannelflow based in Atlanta, GEORGIA (US) (USA). from Flumes Product line

  • Nautilus - Model T-ULH - Ultra Low Head Turbine

    The T Ultra Low Head turbine (T-ULH) is the most powerful open flume turbine built by Nautilus. This unregulated design produces from 500 watts to 3,300 watts with a head range from 1m to 3.7m. Often two or three units are installed to match streamflow variation or the T-ULH is installed in combination with the Regulated CMC. For large open flume ...

    By Nautilus LLC based in Greenfield, MASSACHUSETTS (USA). from Ultra Low Head Turbine Product line

  • Flume Hook

    A 2 in 1 tool: 1. Separates planks. 2. Pulls staples for removing planks in flumes. 60' all metal or wood handle available.

    By Hayden Manufacturing Company, Inc. based in West Wareham, MASSACHUSETTS (USA). from Flume Hook Product line

  • EFC - Parshall Flumes - Fiberglass Composite Buildings

    EFC offers a full line of high quality Parshall flumes designed for use in the metering of liquids in open channels and are also used in pipeline applications. EFC's Parshall flumes are made of corrosion resistant materials to ensure long life and are created with molded one-piece construction with integral stiffening ribs for high strength and ...

    By Engineered Fiberglass Composites Inc based in New Lisbon, WISCONSIN (USA).

  • Spagco - Parshall Flumes

    Spagco Parshall Flumes are constructed from a fiberglass composite constructed of two fiberglass skins with a polymer concrete core. All Spagco flumes have a total wall thickness of 1 ½”. Due to the high moment of inertia of the wall due to the thickness, no stiffeners or other braces are required. The superior strength of the ...

    By Glass-Steel, Inc. based in Conroe, TEXAS (USA).

  • Palmer Bowlus Flumes

    Kenco Palmer-Bowlus flumes are designed and manufactured to meet or exceed the needs of the wastewater and chemical industry. With over 35 years of manufacturing fiberglass products and providing our customers quality service, Kenco Plastics has developed an enviable reputation. Our flumes include features and benefits such as the following:

    By Kenco Plastics, Inc. based in Lewisburg, TENNESSEE (USA).

  • Plasti-Fab - Fiberglass Palmer-Bowlus Flumes

    The Palmer-Bowlus flume is well know in the sanitary field, and has been used in the Los Angeles area for over 60 years. It’s primary application is in pipelines, in round bottom channels or in manholes where it is often preferred because of cost and ease of installation that can minimize construction expense.

    By Plasti-Fab, Inc. based in Tualatin, OREGON (USA). from Fiberglass Palmer-Bowlus Flumes Product line

  • Plasti-Fab - Large Trapezoidal Flumes

    Trapezoidal flumes fall into two principal groups, 60º V-notch flumes and larger trapezoidal flumes. The 60º V flumes have a sharp V-throat section similar to a V-notch weir and produce superior resolution for accurate flow measurement down to 1 gpm. The larger trapezoidal flumes, up to the 2 foot SRCRC flume, have flat floors and ...

    By Plasti-Fab, Inc. based in Tualatin, OREGON (USA). from Large Trapezoidal Flumes Product line

  • EFC - Fiberglass Reinforced Polyester Palmer-Bowlus Flumes

    EFC's high quality Palmer-Bowlus flumes are designed for use in the metering of liquids in pipelines and round bottom open channels. Corrosion resistant materials are used in the construction of these flumes to ensure long life. Molded one-piece construction generates high strength and rigidity. A smooth gelcoat finish is applied on the interior ...

    By Engineered Fiberglass Composites Inc based in New Lisbon, WISCONSIN (USA).

  • Cutthroat Flume

    Cutthroat flumes are ideal for measuring water flow rates. Applications include: stream surveys, well pumping tests, irrigation studies, drainage surveys, seepage inspections, industrial outflows, sewage treatment plant flows, mine drainage, tail water runoff, and spring discharge. The name 'cutthroat' comes from the fact that there is no parallel ...

    By Baski, Inc. based in Englewood, COLORADO (USA). from Cutthroat Flume Product line

  • Palmer Bowlus and Parshall Flumes

    Warminster Fiberglass makes both Palmer-Bowlus and Parshall Flumes. They are used to measure flows in open channels and pipelines. Both types are precision molded of fiberglass reinforced polyester for light weight and corrosion resistance. They both are available with a smaller flume 'nested' inside, as shown in the above Parshall Flume (on the ...

    By Warminster Fiberglass Company based in Southampton, PENNSYLVANIA (USA).

  • Dry Belt for Sorting & Laborers Tend

    Dry belting is suitable for sorting, laborers tend to prefer dry belting for comfort reasons, Available in multiple lanes with variable speed control, and cull return available in water flume or belt conveyance. Traditional white belting is being succeeded in the industry by colored belting because it does not reflect as much light and is easier ...

    By Munckhof Manufacturing based in Oliver, BRITISH COLUMBIA (CANADA). from Dry Belt for Sorting & Laborers Tend Product line

  • Plasti-fab Fiberglass and Composite Head Gages

    Plasti-Fab has made FIBERGLASS HEAD GAGES for use in open channel flumes for over 20 years. Due to market demand, we now offer this same durable construction in all sizes of custom level fiberglass gages.

    By Plasti-Fab, Inc. based in Tualatin, OREGON (USA). from Plasti-fab Fiberglass and Composite Head Gages Product line

  • Rotary Drum Cooker Cooler

    Combination Blancher/Cooker-Coolers were first designed in 1995 for blanching or cooking vegetables, and pasta, but not long after that were redesigned to be Pasteurizer/Coolers. The basic differences between a blancher, cooker or pasteurizer are retention times and operating temperatures. Blanchers normally operate at a short time, and higher ...

    By Lyco Manufacturing, Inc. based in Columbus, WISCONSIN (USA). from Rotary Drum Cooker Cooler Product line

  • Rotary Drum Cooker

    Combination Blancher/Cooker-Coolers were first designed in 1995 for blanching or cooking vegetables, and pasta, but not long after that were redesigned to be Pasteurizer/Coolers. The basic differences between a blancher, cooker or pasteurizer are retention times and operating temperatures. Blanchers normally operate at a short time, and higher ...

    By Lyco Manufacturing, Inc. based in Columbus, WISCONSIN (USA). from Rotary Drum Cooker Product line

  • NSF - Model 61 - Parshall Flumes

    MFG Water Treatment Products’ Parshall flumes are used to measure liquids in open channels, including industrial discharge and a wide range of influent/effluent liquids. Our NSF 61 Parshall flumes ensure that the unbroken flow lines do not obstruct flow which can cause build-up of debris. The unbroken lines also result in low head loss ...

    By Molded Fiber Glass Water Treatment Products (MFG) based in Union City, PENNSYLVANIA (USA). from Parshall Flumes Product line

  • Partrac - Benthic Flumes

    We operate two benthic flumes for the in situ measurement of sediment stability - these are seabed lander systems designed for coastal and offshore use. The flumes are submersible marine instruments which rest unattended on the seabed and apply a controlled flow across the seabed. Sensors are used to measure seabed erosion as it occurs, typically ...

    By Partrac Ltd based in Glasgow, UNITED KINGDOM.

Need help finding the right suppliers? Try XPRT Sourcing. Let the XPRTs do the work for you