Pipe Sealing Applications

15 Results found
Only show results in Virginia?
OK
  • Category: Water & Wastewater ×

  • Subcategory: Pipe Sealing ×

Innovative pump technology for oil and gas industry

by EDUR-Pumpenfabrik Eduard Redlien GmbH & Co. KG     based in Kiel, GERMANY

Medium-specific solutions, equipped with oil and gas tested materials and components, dimensioned for each application. Our engineers have the task of finding an energy-efficient, safe and powerful EDUR solution for this.

PEHD membrane sealing systems for basins

by ELD Environmental Leak Detection GmbH     based in Berlin, GERMANY

For reasons of environmental protection, basins often need to be leakproof, e.g. seepage basins on landfill sites. However, it can also be important to ensure, for example, that valuable water does not escape into the subsoil undetected.

Facilities management in line air flow meter solutions

by Sierra Instruments, Inc.     based in Monterey, CALIFORNIA (USA)

Sierra’s offers a complete line of precision flow solutions for any gas, liquid or steam measurement to improve energy efficiency in all facilities management applications. Our mass vortex meters are used to allocate steam, our in line thermal mass flow meters track and allocate natural gas and compressed air usage, and our clamp-on and insertion ultrasonic meters provide accurate water and water-based fluid measurement.

Hose pumps for copper mining industry

by Albin Pump SAS     based in Goteborg, SWEDEN

Copper tailings - slurry is very abrasive. Centrifugal pumps with soft packing shaft seals had to be water-flushed to limit wear on the shaft sleeve. Fine until winter froze the water. Solution: a Albin Pump ALHX80, with no seals to wear out. Tailings could be continuously pumped at higher concentrations!, doubling plant efficiency. Downtime: a few minutes every 2,000 hours to change the tube.

PEHD membrane sealing systems for retrofitting in existing landfill site

by ELD Environmental Leak Detection GmbH     based in Berlin, GERMANY

It is also possible to retrofit a monitoring system in existing surface sealing liners without impairing the synthetic liner sheet or the immediately adjacent functional layers. For this purpose, cable trenches must be dug in the recultivation layer above the drainage layer. The detection cables are then laid in these trenches.

PEHD membrane sealing systems for landfill surface liners

by ELD Environmental Leak Detection GmbH     based in Berlin, GERMANY

Unlike base liners, surface liners are not buried at some point under many metres of waste and instead are usually protected over the course of many years only by a 1-metre thick mineral layer. As a result, there can be uncertainty about the integrity of their leak-proofing characteristics, particularly if the land is subsequently used for other purposes; however, at the same time, repairs are also possible at reasonable cost if the location of any damage can be established.

Mixers, dryers, innovative solutions for pharmaceutical industry

by AVA - Huep GmbH u. Co. KG     based in Herrsching, GERMANY

As a supplier of machines and installations to the pharmaceutical industry, we ensure that these comply with current GMP regulations and are FDA compliant. Furthermore, we guarantee that they are delivered with all required certification and help our customers to conduct risk analyses (RA). We take our service to the next level by supporting the procurement and validation process with our FAT and SAT protocols and with Installation Qualification (IQ), Operational Qualification (OQ), and Performance Qualification (PQ). We also conduct operator training and carry out plant maintenance.

Innovative pump technology for cooling and refrigeration industry

by EDUR-Pumpenfabrik Eduard Redlien GmbH & Co. KG     based in Kiel, GERMANY

Transporting cold liquids in cooling and refrigeration systems places high requirements on the pump used. For reliable, constantly high pump performance the pump has to be designed accordingly, dimensioned specifically for the application and fitted with special equipment for the low temperatures.

Leak sealing solutions for wastewater

by SealGuard Inc.     based in Gibsonia, PENNSYLVANIA (USA)

Manhole Rehabilitation: Pipe sealing. SealGuard II High Flow repair. Barrel Joint or Low Flow crack HyperFlex repair. Curtain Grout w/soil rods or pattern grouting. Leaking Boot. Annulus Grouting (pipe within pipe).

Variable frequency drive controls AC motors

by Variable Frequency Drives     based in NSW, AUSTRALIA

Consider integrating a variable frequency drive. It often can optimize energy efficiency by enabling you to match motor speed to the demands of the system. Look for opportunities, for example, to replace throttle valves or dampers used to restrict flow. However, a variable frequency drive may not make sense if the load on the motor is relatively small and constant — because speed changes will occur infrequently and any benefits from varying the speed will be negligible. So, thoroughly assess the system load profile to determine the scale and frequency of required speed changes before deciding about installing a variable frequency drive.

Pumps for Paint & Ink

by DESMI A/S     based in Noerresundby, DENMARK

Coloured and protected surfaces provide added value as paints and enamels help to make products both more interesting and increase their life. That is why they are important finishing materials where care, environmentally-friendliness and reliability are needed in their supply and correct dosage. The DESMI ROTAN® gear pumps are commonly used for paints, resins and coatings. For ink manufacturing and printing press applications, the HD series and specially fitted PD and ED magdrive pumps are being used. A leading paint factory manager, states: “ROTAN® pumps have for decades been used in numerous of our plants. The ED model was chosen due to its magnetic coupling. A magnetically coupled design, which has no rotating seals, ensures less downtime and lower operating costs. Every pump in our new facility is magnetically coupled, and thus we have eliminated the problems associated with packed glands and mechanical seals.”

Pumps for Asphalt / Bitumen

by DESMI A/S     based in Noerresundby, DENMARK

DESMI has a full range of different pumps and matching equipment supporting the handing of bitumen products. Including unique features suited for today’s needs and new polymer based formulations, we have the solution. For certain applications, we can offer proven sealing options, available is also a patented zero-leakage pump with a state of the art magnetic coupling. This pump offers a total protection against spillage and vapour, which may create environmental hazards. Electrical heating is an alternative to heating by liquid or steam. Applications tend to fall into four categories: Production (refining), distribution (terminals), hot mix (paving mixtures), and roofing (filled asphalts). Refineries and terminals often use steel pumps, while hot mix asphalt plants use mainly cast iron pumps with heating jacketed, and either packing or mechanical seals. Roofing plants are generally pumping highly abrasive, filled asphalts for shingle manufacturing.

PEHD membrane sealing systems for storage areas

by ELD Environmental Leak Detection GmbH     based in Berlin, GERMANY

Areas used to store substances which could represent a hazard if they escape into groundwater must also be leakproof in case accidents occur.

PEHD membrane sealing systems for landfill base liners

by ELD Environmental Leak Detection GmbH     based in Berlin, GERMANY

There are several phases of preparation of landfill base liners, starting with the positioning of the membrane, until these can be covered with several metres of refuse. These membranes may be damaged during preparation, but can also be inspected and repaired. It is advisable to undertake inspections at regular intervals.

PEHD membrane sealing systems for dams

by ELD Environmental Leak Detection GmbH     based in Berlin, GERMANY

In the mining industry, dams are built in order to create large storage basins.

Need help finding the right suppliers?

Let the XPRTs do the work for you