CONBAR ep products

Our fixed length sampler allows the sample to be taken directly into a sampling container. The samplers are available with a 960ml plastic wide mouth jar or a 1L glass jar. Both samplers incorporate our swivel adapter, which allows the container to rotate almost 360 degrees. This swiveling action allows samples to be taken from almost any angle.

Our  Telescopic Sampler is manufactured using locking telescopic aluminum tubing and is available in lengths up to 24` The sampler incorporates a threaded polyethylene head that swivels almost 360 degrees. The 5380 series head accommodates a 960 ml plastic jar while the 5385 series accommodates a 1L glass jar. In operation, the sampler is quick and easy to use.  Just screw in the jar, extend the telescopic handle to the desired length, and lower the sampler into the liquid to be sampled. Each sampler is supplied complete with one sampling jar.  

The Swing Sampler is designed to collect samples from a horizontal flowing stream, such as a sewer. The swing jar holder allows for collection angles up to 90 degrees. The sampler is manufactured from telescoping fiberglass poles and is available in two sizes - 6` to 12`, and 8` to 24`. The sampler is supplied complete with one plastic clamp, which holds the bottle in place, and one plastic 960ml sampling bottle.   

Specially designed with an inside diameter if 1 3/8` to allow for the passage of large solid particles during sampling of grease holding tanks. The clear tubing is easy to see through and the 1-foot markers show the depth of the submersion into the tank. When the unit is lowered into the liquid, the float valve opens, allowing the sample to flow in. Upon reaching the bottom, the unit is raised up and the valve closes, holding the sample inside. The mixture is then visible, showing the level of grease and liquid in the tank. The sampler is made of two 4-foot sections that screw together and can be purchased with additional 4` extension sections for sampling deeper tanks.

The NASCO Sludge Nabber makes sample collection of liquids fast and easy. It has an adjustable aluminum pole that extends from 4 to 6½, feet, making it easy to reach the liquid to be sampled and carried. The Sludge Nabber is ideally suited for numerous sampling requirements including chlorine in solution. Sample bottles of various sizes (250 ml to 1000 ml) are held in a polyurethane holder by a plastic snapper ring that has an adjustable locking device. Whether testing for chlorine, BOD (biochemical oxygen demand), or SS (suspended solids), the Sludge Nabber`s flexibility with holding various bottles, and its adjustable length, allows for effortless sampling. Unit is supplied with one 500-ml polyethylene bottle and one small snapper clamp. See accessories below.  

Save time and money by eliminating sampler cleaning costs and cross-contamination problems. Each sterilized sampler is individually wrapped and ready to use. The samplers are easy to use. To operate - push the sampler into the product, rotate handle to open sampler, allow a few seconds for the sampler to fill, rotate the handle closed and remove sample. Slide the inner rod out of the outer tube to remove the extracted sample.

These nylon brushes are specifically designed to clean most common sizes of bailers.  Each brush has a nylon head 4-3/4" long and has an overall length of 42",  which allows the brush to be used when cleaning bailers up to 3 feet long when cleaning from one end, and up to 6 feet long when the bailer can be cleaned from both ends.

The CONBAR stainless bomb samplers are manufactured from a high quality corrosion resistant type 304 stainless steel. The bomb samplers  are designed to collect liquid samples from storage tanks, lakes, ponds, manholes, wells, and other hard to reach places. The plunger assembly will be activated automatically when the sampler contacts a hard surface such as the bottom of a tank, or it may be activated by the operator at various depths with the use of a pull line. A Viton® `O` ring insures the integrity of the sampling chamber until the plunger is activated.

The brass-bronze composite, or average, bomb sampler is equipped with an adjustable needle valve to control the liquid rate of fill.  When lowered into a tank or liquid container, liquid flows into the lower end of the sampler at the rate that the air is being displaced through the needle valve or plug assembly. If the sampler is lowered at a uniform rate, the sample collected will be a composite sample of the tank`s contents. The sampler can be easily disassembled for cleaning by unscrewing the top and bottom caps.

Manufactured from brass and bronze, then nickel plated, these samplers are designed to extract samples from drums, tanks, tank cars, wells, and ponds. The plunger assembly will be activated automatically when the sampler contacts a hard surface such as the bottom of a tank, or it may be activated by the operator at various depths with the use of a pull line. This feature allows samples to be taken at random depths. When raised, the plunger automatically reseals closing off the inlet port, locking the sample in place.