Model 1001 BarrierFree Drinking Fountain Spec Sheet

model 1001 Wall-Mounted Drinking FountainFEATURES & BENEFITSQUALITY CONTROLFountain is pre-built and fully water and pressure tested toensure no leaks and proper function for reducedinstallation time and added peace of mind.BUBBLER HEADPolished chrome-plated brass bubbler head with integrallaminar flow prevents splashing and provides a superiorflow pattern. The integral basin shank and inserted roll pinadds vandal resistance strength to the design, and theshielded angled stream orifice produces a steady sanitarysource of water.MOUNTING3/16" (.47 cm) steel mounting plate with supplied mountinghardware provides a solid unit base and allows for easyinstallation to a framed wall. (P-trap and stop require rearaccess)PUSH BUTTONWith its patented (Pat. # 6,981,692) stainless steel,push-button activated valve assembly which allows forfront access stream adjustment as well as cartridge andstrainer access, this fountain offers 100% lead freewaterways. The valve works at an operating pressure rangeof 30 to 90 psi (2.1 to 6.2 bar).OPTIONSFilter: Model 6426, 12" x 2" (30.5 x 5.1 cm), in-line leadremoval element that reduces lead from incoming watersupply.Access Panel: Model 6603, satin finish stainless steel accesspanel. Includes frame and screws.Support Carrier: Model 6800 universal in-wall mountingsupport for use with most fountains.Back Panel: Model BP6, satin finish stainless steel backpanel.To see all options for this model, visit www.hawsco.comSPECIFICATIONSModel 1001 wall mounted barrier-free drinking fountain shallinclude an 18 gauge Type 304 Stainless Steel satin finish basinwith integral swirl design, 14 gauge Type 304 Stainless Steelwall bracket, 100% lead-free waterways, push-buttonoperated stainless steel valve with front-accessible cartridgeand flow adjustment, polished chrome-plated brassvandal-resistant bubbler head with integral laminar anti-squirtflow, chrome-plated brass vandal-resistant waste strainer,vandal-resistant bottom plate, and 1-1/4" O.D. (3.2 cm) wastepipe. (P-trap and stop require rear access) REQUIRES MODEL6700 PRICED SEPARATELY.APPLICATIONSPerfect for either public or private indoor/outdoor settings,Model 1001 is a great fit in areas where aesthetics areimportant to the overall appeal of the architecture. This seriesis precisely mounted, making it a nice addition to anysurrounding. Beautiful satin finish helps to maintain thefountains overall appeal so it always remains looking as newas it did when it was installed. Specifically, this type of wallmounted drinking fountain may be placed in settings such as:schools and other locations in and around office buildingswhere the temperature remains above freezing.Model meets all current Federal Regulations for the disabledincluding those in the Americans with Disabilities Act. Hawsmanufactures drinking fountains and electric water coolers tobe lead-free by all known definitions including NSF/ANSI 61,Section 9, NSF/ANSI 372, California Proposition 65, and theFederal Safe Drinking Water Act. Product is compliant toCalifornia Health and Safety Code 116875 (AB 1953-2006).1455 Kleppe Lane :: Sparks, NV 89431 :: p. 775.359.4712 :: f. 775.359.7424 :: e. info@hawsco.com :: www.hawsco.com :: 05 May, 2013DISCLAIMER: Continued product improvements make specifications subject to change without notice. Check www.hawsco.com for the latest product information and updates.1. HOLD ROUGH-IN DIMENSIONS ±1/8" (3.2mm).2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES SHOULD BE ADHERED TO FOR INSTALLATION DIMENSIONS (LOCATIONS), WASTE AND SUPPLY REQUIREMENTS OTHER THAN SHOWN. INSTALLER MUST PROVIDE TRAP FOR PROPER INSTALLATION. REMOVE VALVE FROM PUSH BUTTON TO INSTALL WASTE ELBOW ONTO BOWL. AFTER WASTE ELBOW IS INSTALLED, REINSTALL VALVE AND ADJUST FLOW.BACK PANEL (OPTIONAL):1001 & 1001HPS(STANDARD):1001BP & 1001HPSBPOPTIONAL TRAP ACCESS PANELMODELS 6603 AND 6603HPSø3/8" SUPPLY TUBINGAND SCREW DRIVER STOP(NOT SUPPLIED)6700 MOUNTING PLATE(BEHIND FINISH WALL)CMOUNTING BOLTS(NOT SUPPLIED)WASTE BEND AND 1-1/4" IPS TRAP(NOT SUPPLIED)AADETAIL C1-1/4" O.D.WASTE BEND(SUPPLIED)6700 MOUNTING PLATEMUST BE INSTALLED BEFOREFINISH WORK. THIS PLATE IS ASTANDARD ITEM.SECTION A-AROTATED 90° INTO VIEWBRACKET MOUNTING DETAILWALL FACEFLOOR LINEWALL STUDWALL FACE3434NOTES:[10]4X ø3/8"[76]3"[51]2"[47]1 27/32"[58]2 9/32"[457]18"[406]16"[127]5"4X 3/8"-16 UNC[178]7"[25]1"[729]28 11/16"SUPPLY[714]28 3/32"WASTE[686]27" [864] 34"(TO SPOUT OUTLET)[473]18 5/8"[76]3"[645]25 3/8"[380]15"[406]16"[359]ø14 1/8"[76]3"[47]1 27/32"[133] 5 1/4"[83]3 1/4"DWG. NO.APPROVED:DRAWN:PART NUMBER:DRAWING NO.:SCALE: SHEET OFREV.DRAWING TYPE:THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTSMAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.SIZE:BY:ECN NO.DATE:DATE:ECN:REVISED PERCHK'D.: Haws Corporation - All Rights Reserved HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.C RSPARKS, NEVADA 89431(775) 359-4712 FAX (775) 359-74241455 KLEPPE LANEE-MAIL: HAWS@HAWSCO.COM WEBSITE: WWW.HAWSCO.COMMODEL(S)15990A00RTM 05/9715990A00 160002076304.D1001/1001BP/1001HPS/1001HPSBPDRINKING FOUNTAIN1:1 1 1AHMINSTALLATION47972012