- Home
- Equipment
Refine by
Icm Environmental Equipment & Supplies
18 equipment items found
Manufactured by:I.C.M. International Construction Machinery S.r.l. based inRavenna, ITALY
ICM makes a broad range of man baskets in steel or aluminium. CB two-person baskets are designed to offer enough space for two people to work at the same time together with all necessary equipment. All baskets are certified according to Norm EN280:2015. They can be equipped with an automatic level control system upon request, so the operator won’t have to use a manual handle to block the ...
Manufactured by:ICM based inNorwalk, CONNECTICUT (USA)
ICM is a prime manufacturer of Hopper Bottom and Space Saver Dust Collectors, Cyclone Separators and After Filtration Systems designed and built to meet the demanding air quality standards of the 21st century. Whatever your particular requirements may be, ICM’s standard products and/or custom solutions will meet your current and future ...
Manufactured by:I.C.M. International Construction Machinery S.r.l. based inRavenna, ITALY
PLY-Z polyp grabs are designed specifically to be installed on Z-folding cranes, to keep within the outline of the truck and not go over the maximum allowed width of 250 cm. This is the function of the PLY-Z’s asymmetrical shape. With an asymmetrical polyp grab you will be able to perform any job as with a “normal” polyp grab. It is available in 320lt capacity. All of the ...
Manufactured by:I.C.M. International Construction Machinery S.r.l. based inRavenna, ITALY
The wide range of PLY polyp grabs allows you to always have the right tool for any kind of job. They can be used in several applications as recycling, garden maintenance, waste collecting and scrap metal handling. They are built with high-quality material to prevent the metal from warping when under heavy strain. All models except the smaller ones sport conical pins, which allow to counterbalance ...
Manufactured by:ICM, Inc. based inColwich, KANSAS (USA)
By removing suspended solids from the process stream, TS4™ improves dryer and evaporator capacities, minimizes energy consumption and enables the production of higher-value feed products. Improving efficiency through solids separation: By removing suspended solids from the thin stillage stream, TS4™ improves efficiency and allows equipment to process stillage at a higher feed rate ...
Manufactured by:ICM, Inc. based inColwich, KANSAS (USA)
The Base Tricanter System™ separates corn distillers oil from syrup. Superior oil recovery for added revenue: ICM’s Base Tricanter System™ employs a three-phase centrifuge to separate the maximum amount of corn distillers oil from syrup. ...
Manufactured by:I.C.M. International Construction Machinery S.r.l. based inRavenna, ITALY
ICM makes a broad range of man baskets in steel or aluminium. One-man baskets are designed to be lightweight, which allows them to be installed on cranes with a relatively low load capacity. All baskets are certified according to Norm EN280:2015. They can be equipped with an automatic level control system upon request, so the operator won’t have to use a manual handle to block the ...
Manufactured by:ICM based inNorwalk, CONNECTICUT (USA)
SuperHone is ICM’s signature line of abrasive dry-blast cabinets. SuperHone is available in a variety of sizes with a generous list of available options. Built to give you many years of faithful, trouble-free service, at minimal ownership cost, this workhorse blasting system is in service around the world in practically any industry you can name. The ICM SuperHone is available as a Style II, for ...
Manufactured by:ICM based inNorwalk, CONNECTICUT (USA)
Our HydroHone line of slurry-blast machines is perfect for jobs too delicate for traditional dry blasting. These versatile machines mix abrasive with water and pump the resulting slurry to the blast gun where it is accelerated by a compressed air jet and aimed at the part. In addition to providing a gentler cleaning action, the wet process is quieter, cooler and ...
Manufactured by:ICM, Inc. based inColwich, KANSAS (USA)
In ICM’s integrated distillation, dehydration and evaporation (DDE) system, each process reuses energy to increase overall plant efficiency. The distillation system uses steam and energy from the evaporation system, and the evaporation system uses heat recovered from the dehydration system and low-pressure steam. The evaporation system eliminates the land application of thin stillage by ...
by:International Climbing Machines (ICM) based inIthaca, NEW YORK (USA)
The ICM dual climber is essentially two standard ICM climbing robots that have been integrated both mechanically and electrically. This gives the dual climber higher payload capacity than a single ICM robot. ...
Manufactured by:ICM based inNorwalk, CONNECTICUT (USA)
The Super Ad-A-Blast is our entry level model, available in either a pressure blast or syphon blast configuration; however, almost any type of surface finish you might want can be achieved by syphon blasting. In a syphon machine blast media are placed in the abrasive storage hopper where vacuum from a venturi in the blast gun pulls it through an abrasive hose. Air and media mix inside the blast ...
Manufactured by:ICM based inNorwalk, CONNECTICUT (USA)
A Blast Room allows the operator to enter the work chamber and directly blast parts that might be too heavy for, or not fit in, a Blast Cabinet. In the most basic Blast Room, the operator sweeps up used abrasive and shovels it into the pressure pot. In a Blast Room with Air Swept Duct(s), the operator manually sweeps abrasive into a duct thus eliminating the shoveling process. Advanced Blast ...
by:International Climbing Machines (ICM) based inIthaca, NEW YORK (USA)
ICM robots can climb on any surface. We have deployed on large concrete structures, stainless steel tanks, bridges, insulated vessels, wind turbine blades, fuselages of airplanes, hulls of ships and nuclear submarines, etc.. There truly is no limit to what ICM robots can climb on. Very importantly, our robots can carry substantial payload. We have integrated many tools onto our climbing robots ...
Manufactured by:I.C.M. International Construction Machinery S.r.l. based inRavenna, ITALY
PLY-W polyp grabs for sawn timber allow the user to lift and handle firewood and sawn timber. Thanks to their shape they allow to pick up the material without risking to lose cargo during handling. I.C.M. polyp grabs for sawn timber can be installed on cranes from 8 to 30 ton/m and excavators from 3 to 10ton of weight. ...
Manufactured by:ICM, Inc. based inColwich, KANSAS (USA)
Our innovative flaking system maximizes oil production and increases ethanol yield. Exposing more starch for ethanol conversion: SMT™ and SMT V2™ unlock the maximum amount of oil and starch in a corn kernel. This patented process bolts onto your existing plant with no risk to prime operations, and it provides the platform for ICM’s FST™ and FST Next Gen™. SMT™ ...
Manufactured by:ICM, Inc. based inColwich, KANSAS (USA)
FOT Oil Recovery™ is a proprietary two-step separation process that frees up more corn oil for recovery. The process also dewaters the whole stillage cake as it goes to the dryer, reducing your plant’s natural gas load. Maximize corn oil recovery: FOT Oil Recovery™ is a proprietary two-step separation process that frees up more corn oil for recovery. The process also dewaters ...
by:International Climbing Machines (ICM) based inIthaca, NEW YORK (USA)
ICM Underwater Climbing Robots can be deployed in tanks, vessels, on ship hulls or other structures. They are held to the surface with suction. This suction can be achieved one of two ways: either with a small pump integrated on the Climber, or with a remotely located pump with a hose from the pump to the Climber. The systems are small and portable and can be set up very quickly for easy ...