- Home
- Equipment
Refine by
Imo Environmental Equipment & Supplies
20 equipment items found
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Imo supplies 3-screw pumps for engine room services such as fuel oil transfer, boost, stripping and burner. Fuels handled, range from heavy bunker fuels to light jet fuels. Imo pumps are also manufactured for lubrication service for diesel engines, gas and steam turbines, reduction gearing, generator sets, blowers and other similar equipment. Pumps can be supplied to commercial marine standards ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The 4SFC series pump is intended primarily as a medium pressure fluid power pump. It is available foot or flange ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The 4VKC series pump is intended primarily as a medium pressure fluid power pump. It is available foot or flange ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Series USNP/4PIC are designed for direct drive via submerged two pole electric motors. They supply pressurized fluid to hydraulic elevator ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The 413IC pump is designed for vertical, deep well submerged operation for unloading barges, small tankers or tanks. The pump discharge is axial along the shaft. The design incorporates a third idler rotor which suppresses vibration and noise when pump is lightly cavitated. ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The Tritec series three screw pumps are designed for handling liquids with little or no lubricating properties, liquids that are corrosive or that contain abrasives. Examples include fresh or sea water, desalinated or deionized water, acid containing liquids, boiler feedwater, caustic solutions, emulsions, naphtha, waste oils and solvents, residual oils, etc. The use of stainless steel casings, ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The 8L series pump is designed for pipeline transport in medium to high pressure service for crude oils, fuel oils and other petroleum products. It also finds extensive use in steam/electric power plants as the burner pumps supplying fuel to the ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
EMTEC pumps are designed to withstand the harsh environment of high pressure machine tool coolant service. Special hardening techniques produce wear resistance within the housing bores offering cost effective ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The 3D series pumps is a general purpose design suitable for many applications including lubrication, fuel transport and burner service, low pressure hydraulic applications and hydraulic elevator service. Pump shaft is generously sized to allow belt drive if desired (mechanical seal versions only). This series is available in magnetic drive ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Series 6D is a medium pressure pump line finding extensive use on fuel oil burners, high pressure trunion lubrication for ball mills, crude oil pipeline service and non-cyclic hydraulic ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The 6U series pump is intended primarily as a high pressure fluid power pump. It is available foot or flange mounted and is suitable for cyclic pressure service. The 6T series is produced in a cast steel casing with a combined foot/flange mounting arrangement. The pump is primarily used for medium pressure gas sealing applications on ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Series 324A is a double suction design providing relatively high flow rates in a compact pump. These are commonly used for machinery lubrication, fuel oil transfer and burner services and for asphalt and vacuum tower bottoms processing and transfer. Pumps are available with optional steel casings with or without steam/hot oil ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
CIG (Crescent Internal Gear) pumps are produced primarily for fluid power applications and aircraft fuel test stands. They are available in multiple stages for very high pressure or moderate pressure on very low viscosity fuels. Pumps are also available in double pump configurations which share a common inlet port but deliver two independent flows for supporting multiple machine functions. ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Series 3G pumps are provided for differential pressures to 250 PSIG (17.2 Bar) and flow rates to 55 GPM (208 L/M). Mountings include foot or flange. Casing materials are either cast iron or steel. These three screw pumps are used for distillate fuel oil transfer and burner services, machinery lubrication and other industrial pumping applications. Most sizes are available with a tamper ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Series 12L pumps are designed for very high pressure service primarily for compressor gas sealing, fluid power and hydrostatic bearing applications. Pumps are equipped with a steel case and balanced mechanical shaft seal. This series is believed to be the world's highest pressure capability 3-screw ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Series 3E pumps are provided for differential pressures to 150 PSIG (10 Bar) and flow rates to 100 GPM (375 L/M). Mountings include foot or flange. Casing materials are either cast iron or steel. These three screw pumps are used for fuel oil transfer and burner services, machinery lubrication and other industrial pumping applications. Units without shaft seals can operate at very high speeds ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Series 12D Imo pumps are intended for relatively high pressure service on petroleum or similar viscosity liquids. Typical applications include crude oil pipeline service, fuel atomization for burning in a steam boiler, fuel injection for combustion gas turbines, fluid power service on hydraulically operated machinery, gas sealing in centrifugal compressors and hydrostatic bearing support. These ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The 4U series pump is intended primarily as a medium pressure fluid power pump. It is available foot or flange mounted and is suitable for cyclic pressure service. The 4T series is produced in a cast steel casing with a combined foot/flange mounting arrangement. The pump is primarily used for medium pressure gas sealing applications on ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
The T324 series is a double suction design for a compact, medium flow, medium pressure pump. It is used extensively for crude oil processing and transport as well as for fuel oil ...
Manufactured by:Imo Pump based inMonroe, NORTH CAROLINA (USA)
Series 323F is a double suction design providing the highest flow rates of any three screw pump. They are found in tank farm services, loading and unloading terminals, power plants and asphalt process and ...