Sauereisen - Model No. 950S - Fluoropolymer Coating
From Corrosion Protection - Accessory Materials - Membranes and Joint Sealants Products
Sauereisen Fluoropolymer Coating 950S is a two-component liquid fluoroelastomer. It will withstand service temperatures up to 400ºF. Sauereisen No. 950-S offers excellent resistance to most acids, alkalies, and solvents common to industrial facilities.
Physical Properties
- Color : Black
- Coverage, cu. in./gal : 36
- Elongation (ASTM D-2370) (Post Cure) : 250%
- Operating Temperature : -40° to 400°F, with excursions to 500°F
- Tensile strength (ASTM D-2370) (Post Cure) : 1,000 psi
- Viscosity, cps : 2,000
- Volume Non-Volatile (ASTM D-2697) : 15.4%
- Weight Solids : 30%
- Density (lb./gallon) : 8.5
- Specific Gravity (Water = 1) : 1.02
Characteristics
- Liquid fluoroelastomer; Coating, Adhesive
- Solvent Borne.
- Two-Component
- Unaffected by temperatures from -40ºF to +400ºF.
- Acceleration Ratio (by weight) 50:1
Area Preparation
Surface Preparation
Substrate should be clean and dry for maximum adhesion. Gritblasting and degreasing with oil-free solvents is recommended.
Applications:
Mixing
Product may settle during storage. Stir the product with a broad spatula or paint stick before adding the accelerator. Make sure to scrape the bottom and sides thoroughly, and check for any undispersed, thicker material which may be clinging to the spatula. Slowly add the accelerator to the base material and mix thoroughly. Avoid any mixing methods which introduce substantial amounts of air into the liquid. After adding the accelerator, put the lid on the container and do not disturb for 10 minutes. This standing time will allow trapped air to escape prior to the application. It is important to keep the lid on the container when the material is not being actively applied. Air exposure allows evaporation of the solvent and increases the viscosity of the material.
Once mixed the 950S has a useful life of approximately 8 hours at 75ºF (24ºC).
Coverage
36 cubic inches per gallon.
Coverage rates are theoretical and will vary depending upon surface conditions, porosity, application techniques, and specific project conditions.
Clean-Up
All equipment should be cleaned with MEK, MIBK, or Acetone.
Setting/Curing
The surface of the material will dry very quickly generally in 20 minutes or less. Thick applications will trap solvents beneath the surface. Allow for solvent evaporation prior to making multiple coats, or blisters may result. Product adheres well to itself. Thin applications will cure in approximately 24 hours at 75ºF. Faster cures are possible by heating solvent free coatings for 20 minutes at 300ºF (149ºC). Thick applications or low temperatures may increase cure time.
Packaging
Accelerator: 77 g (98ml)
Base: One Gallon
Shelf Life
Fluoropolymer Coating 950S Base Material and Accelerator have a shelf life of 12 months from the date of certification when stored in unopened, tightly sealed containers in a dry location at 70ºF. If there is a doubt of the quality of the materials, contact Sauereisen.
Safety
Flammable Liquid: Use in accordance with the Safety Data Sheet.
Caution
Consult Safety Data Sheets and container label Caution Statements for hazards in handling these materials.
Warranty
We warrant that our goods will conform to the description contained in the order, and that we have good title to all goods sold. WE GIVE NO WARRANTY, WHETHER OF MERCHANTABILITY, FITNESS FOR PURPOSE OR OTHERWISE, EXPRESS OR IMPLIED, OTHER THAN AS EXPRESSLY SET FORTH HEREIN. We are glad to offer suggestions or to refer you to customers using Sauereisen cements and compounds for a similar application. Users shall determine the suitability of the product for intended application before using, and users assume all risk and liability whatsoever in connection therewith regardless of any suggestions as to application or construction. In no event shall we be liable hereunder or otherwise for incidental or consequential damages. Our liability and your exclusive remedy hereunder or otherwise, in law or in equity, shall be expressly limited to our replacement of nonconforming goods at our factory or, at our sole option, to repayment of the purchase price of nonconforming goods.
- Distributors and agents in major cities throughout the world. Consult manufacturer for locations.
- Information concerning government safety regulations available upon request.
- Sauereisen also produces inorganic compounds for assembling, sealing, electrically insulating and grouting
Customer reviews
No reviews were found for Sauereisen - Model No. 950S - Fluoropolymer Coating. Be the first to review!