- Home
- Companies
- Core Sensors LLC
- Products
- Core Sensors - Model CS54 - ...
Core Sensors - Model CS54 -Non-Incendive Differential Pressure Transducer
The CS54 Non-Incendive Differential Pressure Transducer is a high strength sensor designed for differential pressure measurements of liquids and gases in Class I, Division 2 hazardous locations. A 316L SS oil filled sensor element provides excellent stability over a wide operating temperature range while offering corrosion resistance against various liquids and gases. Differential pressure ranges up to 50 PSI are available with 1/4″ MNPT or FNPT process connections.
- CSA Class I, Division 2, Groups A, B, C, D T4 Approved
- Differential pressures from 1 PSI up to 50 PSI
- Line pressures up to 500 PSI
- Bi-directional pressure ranges available
- Assembled in New Jersey, USA
- Filtration
- Cryogenic bulk tank level measurement
- Compression systems
- Test stands
Available With A Turck Minifast Connection
In an effort to simplify installation in Class I, Division 2 hazardous locations, the CS54 Non-Incendive Differential Pressure Transducer is offered with an integral Turck Minifast electrical connection.
When combined with a CSA Division 2 approved Turck cordset and a Turck Lokfast Guard, there is no requirement for conduit to be installed over the cable*. This not only makes installation easy but also makes switching out sensors less cumbersome. Core Sensors can supply all components as a complete package. Click here to learn more about the Turck Minifast electrical connection.
Accuracy @ 25°C*
≤ ± 0.25% BFSL
≤ ± 0.5% BFSL (2 PSI & below)
Stability (1 Year)
≤ ± 0.25% of FS
Pressure Cycles
4 million
Max Line Pressure**
500 PSI
Max Differential Pressure
50 PSI
Overpressure***
2X or 500 PSI, whichever is less, configured differential pressure
Burst Pressure***
3X configured differential pressure
* Accuracy includes non-linearity, hysteresis and non-repeatability
** Max line pressure is the highest common mode pressure that can be applied to the sensor without damage.
*** Overpressure and burst pressure are the maximum differential pressure that can be applied to the high or low side before damage to the sensor will occur.
Operating Temperature
-40 to +80°C
Operating Temperature
(Electrical connection “F”, DIN 43650-A)
-20 to +80°C
Media Temperature
-40 to +125°C
Media Temperature
(Electrical connection “F”, DIN 43650-A)
-40 to +105°C
Compensated Temperature
0 to +55°C
Storage Temperature
-40 to +125°C
TC Zero
≤ ± 1% of FS
≤ ± 2% of FS (2 PSI & below)
TC Span
≤ ± 1% of FS
≤ ± 2% of FS (2 PSI & below)
EMI/RFI Protection
Yes
IP Rating*
IP65 minimum
Vibration
10g, 20 to 5000Hz
Shock
100g, 11msec, 1/2 sine
* IP Rating is dependent on electrical termination selected. Contact factory for more information.
* IP Rating applies when electrical connector is attached with the appropriate ingress protection.
Outputs
4-20mA
Excitation
10-28VDC
Current Consumption
20mA, typical
Output Load
0-800 Ohms @ 10-28VDC
Frequency Response (min)
~250Hz
Zero Offset (of FS)
≤ ± 0.5% typical, ± 1% max
Span Tolerance (of FS)
≤ ± 0.5% typical, ± 1% max
Outputs
1-5V
Excitation
10-28VDC
Current Consumption
<10mA
Output Load
5K Ohms, min
Frequency Response (min)
~1kHz
Zero Offset (of FS)
≤ ± 0.5% typical, ± 1% max
Span Tolerance (of FS)
≤ ± 0.5% typical, ± 1% max
Outputs
0.5-4.5V ratiometric
Excitation
5VDC +/- 0.5V
Current Consumption
<10mA
Output Load
5K Ohms, min
Frequency Response (min)
~1kHz
Zero Offset (of FS)
≤ ± 0.5% typical, ± 1% max
Span Tolerance (of FS)
≤ ± 0.5% typical, ± 1% max
Outputs
0.5-2.5V non-ratiometric
Excitation
3-5VDC unregulated
Current Consumption
≤ 3mA
Output Load
5K Ohms, min
Frequency Response (min)
~1kHz
Zero Offset (of FS)
≤ ± 0.5% typical, ± 1% max
Span Tolerance (of FS)
≤ ± 0.5% typical, ± 1% max