Applications

A large selection of panel mounted pumps and pump heads for use in Original Equipment Manufacture (OEM). These pumps are custom engineered to integrate within your own equipment whenever accurate and repeatable dosing or liquid transfer is a must. Pumps can be supplied with a range of power options including both A.C or D.C. motors.

By Verderflex Peristaltic Pumps - part of the Verder Group based in Castleford, UNITED KINGDOM.

One-time, on-site final destruction of particulates. This is the key benefit gained from an Anguil solution to the emissions generated by the rubber curing process. Other advantages of an Anguil solution include the elimination of visible blue haze, guaranteed destruction efficiency compliance, and the elimination of costly mechanical filtration media and the lingering liability issue associated with filter disposal.

By Anguil Environmental Systems, Inc. based in Milwaukee, WISCONSIN (USA).

All types of ceramics from fine china to brick manufacture use materials which are extremely hard on pumps. The daily wear on plant and the cost of rejected product can be enormous, and the constant need for manufacturers to drive down costs make savings in these areas vital.

By Watson-Marlow Fluid Technology Group based in Falmouth, UNITED KINGDOM.

All customers have their own individual requirements and specific general conditions. So our experts use their extensive engineering skills and work closely with the customer to develop the right solution every time. This produces a wealth of different applications, which have been used in numerous projects around the globe over the last five decades. With a clear structure of "problem – solution – result", our references from various industries worldwide provide a good starting point and assistance.

By ProMinent Group - ProMinent GmbH based in Heidelberg, GERMANY.

Crystal-clear water in zoos and aquariums. Fresh water = marine animals and sea dwellers full of energy. By reliably treating salt water and fresh water, ProMaqua technology creates the optimum conditions for sharks, polar bears, turtles and other marine animals.

By ProMinent Group - ProMinent GmbH based in Heidelberg, GERMANY.

In many different industries manufacturing processes cause offensive odours in the process air. The Aerox-Injector can be the perfect solution to bring back emission of odours to a minimum.

By Aerox B.V. based in Vleuten, NETHERLANDS.

While land-based industry has been subject to strenuous emissions regulations over the past decades, air emissions from sea-going ships’ machinery has so far been largely unregulated. As a result, according to EU statistics, ships have become the single biggest source of sulphur dioxide (SO₂) within the EU. The US EPA (US Environmental Protection Agency) reports similar findings, i.e., that the proportion of air pollutants released which can be attributed to the shipping industry is increasing. MARPOL Annex VI aims to reduce emissions from ships through international regulations, which hopefully will discourage states from enacting unilateral regulations problematic to the shipping industry.

By Codel International Ltd based in Bakewell, UNITED KINGDOM.

Equipment and Engineering offers the right solution for your application of Kurita Products. Starting from simple dosing pumps up to specific dosing systems for special applications Kurita provides you the right solution for your application. Moreover Kurita offers also monitoring and control equipment to analyze that the right concentration of your Kurita products is being used in your system. Further Kurita provides specific equipment to follow the KPIs of your system, so you can be sure that the expected treatment effect is achieved.

By Kurita based in Tokyo, JAPAN.

WesTech partners with manufacturing in every industry worldwide. For raw water treatment, wastewater treatment and water reclamation, process equipment supplied and manufactured by WesTech is designed to work and built to last. Design-build, plant expansions, and upgrades are each approached from a holistic view of the flow sheet and a broad base of experience in yours and other industries with similar challenges, always with an eye for efficiencies that go to the bottom line.

By WesTech Engineering, Inc. based in Salt Lake City, UTAH (USA).

By Teledyne API based in San Diego, CALIFORNIA (USA).

Production of aluminum from its ores at aluminum smelters results in carbon dioxide CO2, carbon monoxide CO, sulfur dioxide SO2, and hydrogen fluoride HF gas emissions during the electrolytic process phase to the atmosphere. The gas emissions need to be monitored. Typically the smelters have emission limit values (ELVs) for sulfur dioxide and hydrogen fluoride emissions. These emissions should be measured accurately and with good precision, to ensure the smelter does not exceed its emission limit values. In addition several fluoride compounds may be produced in the electrolytic bath in the event of an oxygen shortage. These compounds include carbon tetrafluoride CF4, hexafluoroethane C2F6, sulfur hexafluoride SF6, and silicon tetrafluoride SiF4. These additional emission components are problematic, as they have high Global Warming Potential (GWP) values. The GWP is a relative measure designed to demonstrate how much heat a greenhouse gas (GHG) traps in the atmosphere. Emission of one kilogram of carbon tetrafluoride into the atmosphere today has the potential of heating the atmosphere as much as 7,000 kilograms of carbon dioxide over the next 100 years.

By Gasmet Technologies Oy based in Helsinki, FINLAND.

Quicker, easier, safer transportation means are required.  Depending on geographical zones, tunnels can be a must to reach your final destination easily. Decades of experience in tunnel constructions with TenCate Polyfelt P have shown that protection geotextiles replaces the need for drainage material around the tunnel lining.

By TenCate Geosynthetics Netherlands bv based in AE in Nijverdal, NETHERLANDS.

The production of rubber tyres consists of several processes that generate odours. These processes emit a large airflow with a typical rubber smell, which is likely to cause problems in the wide area of the factory.

By Aerox B.V. based in Vleuten, NETHERLANDS.

TenCate geosynthetics enhance the performance and the design life of railway construction structures.  For these applications, a TenCate geosynthetic is installed as separation and filter layers in areas where groundwater is a problem. TenCate geosynthetics offer the ideal characteristics of robust mechanical properties coupled with high water flow capabilities.

By TenCate Geosynthetics Netherlands bv based in AE in Nijverdal, NETHERLANDS.

Safe handling of liquid chemicals. Safety is our main priority! ProMinent components ensure that dangerous substances are handled safely. Smoothly. Reliably. And intelligently.

By ProMinent Group - ProMinent GmbH based in Heidelberg, GERMANY.

In some countries they do not allow tunnel atmosphere monitors to be mounted on the tunnel wall; also, where there is a single bore it is very difficult to gain access for maintenance purposes. The TunnelTech 400 series are extractive gaseous pollutant and visibility monitors and extract a gas and dust sample from the tunnel bore and carry to a remote analyser. This allows maintenance to take place without affecting tunnel traffic flow.

By Codel International Ltd based in Bakewell, UNITED KINGDOM.

Tunnel ventilation systems are designed to enable a sufficient throughput of air to be maintained to ensure a safe operating environment for users. These systems consume large amounts of power and need to be operated as efficiently as possible. To do this it is necessary to know the effectiveness of the system in terms of air flow and direction developed within the tunnel. The TunnelTech 301 is a single point ultrasonic flow monitor that is unaffected by traffic flow and sound reflections. It is designed to withstand the harsh tunnel environment and has a working range of 0-20 metres/second in both directions.

By Codel International Ltd based in Bakewell, UNITED KINGDOM.

By Aerzener Maschinenfabrik GmbH based in Aerzen, GERMANY.

Watson-Marlow products are engineered to meet the process needs of industrial fluid pumping in a broad range of industries. Watson-Marlow peristaltic pumps have no valves, seals or glands, and the fluid only comes into contact with the bore of the hose or tube ensuring that safe containment and no contamination of the pump or the process fluid.

By Watson-Marlow Fluid Technology Group based in Falmouth, UNITED KINGDOM.

Watson-Marlow positive displacement pumps provide reliable and low cost transfer of fluids for the widest range of equipment and plant applications.

By Watson-Marlow Fluid Technology Group based in Falmouth, UNITED KINGDOM.