Bionomic Industries Inc articles

In process manufacturing of a ScrubPac Thermal Oxidizer Scrubber System with Quencher and pump skid components shown. Scrubber system designed to remove HCL for meeting Pharmaceutical MACT standards. System designed to clean over 61000 ACFM of 1700 deg. F oxidizer exhaust gas.

Kvaerner Metals recently specified 2205 duplex stainless steel for several pieces of equipment to be used in a direct reduced iron (DRI) production facility. RA 2205 was used for two venturi scrubber units as well as two separation units. The design of the equipment was performed by Bionomic Industries of Mahwah, NJ. Douglas Brothers Inc. of Portland, ME was selected to fabricate the units.

The units were shipped to a new plant under construction to produce DRI briquettes, which ar

The installation of Bionomic Industries Inc.`s (Mahwah, NJ) innovative ScrubPac.

BIONOxSOLVER" abatement system is enabling American Superconductor Corporation to treat the nitrogen oxide (NOx) emissions from a calcination process at its new, high temperature superconductor manufacturing facility (Devens, MA), in a cost-effective, environmentally responsible way.

Bionomic Industries` solution uses a unique catalyst oxidation process to convert the nitric oxide to nitroge

While the aroma of a cooked steak may be enticing to some, residents near a cooked-meat facility did not appreciate it.

Polarized Meat Company of Dunmore, PA produces high-quality meat products designed to reduce preparation time at restaurants. Certain products are preformed and pre-cooked, often with grill marks added to enhance the products` visual appeal and flavor. Both the incoming meat and the final products are quality controlled throughout the process.

Given the

Halogenated volatile organic solvents are found in the soil or ground-water at many former and active industrial sites. Fortunately highly effective remediation technologies are available to restore these former brownfields to a healthy state.

The range of technologies includes the traditional approach where the contaminated soil is excavated and the volatile halogenated contaminants are thermally or atmospherically stripped, followed by thermal oxidation of the vapors and scrubbin

While it`s not always easy to determine what`s required for compliance, new technologies can help achieve air-pollution control

Selecting air-pollution control equipment can be tricky. It`s not only difficult to determine which pollutants must be controlled, but also which type of equipment will best control them to required levels for any given process or facility because there is no "one-size-fits-all" solution. Technologies that successfully control pollutants in o

As part of our nation`s program to reduce dependence on fossil fuels, various gasification technologies are being applied. These processes take renewable organic material and, through the application of heat and pressure, convert the materials into syngas for further use. Arguably, in nearly all of these processes, the most critical design aspect is the reliable and efficient removal of contaminant, particulate, gases, and unnecessary water vapor from the syngas stream. Complicating the gas c

Disposing of nearly 1 million pounds of medical waste a month is no easy task. The wet electrostatic precipitator, installed at Rochester, MN-based Mayo Clinic, seems to be just what the doctor ordered.

While the medical waste incinerator at Mayo Clinic in Rochester, MN, consistently met state and federal emission requirements, facility leadership recognized that installing a wet electrostatic precipitator (WESP) on| the pollution control equipment would enable the facility to incr

Flux force condensation scrubbing technology is used to capture fine (submicron) particulate at extremely high efficiency. It is a preferred method when using wet scrubbing to collect and control dioxins from combustion sources. As an added benefit, through the use of condensation, the water vapor plume commonly associated with a wet scrubbing system can be effectively eliminated. The overall collection efficiency of acid gases plus particulate is greater than with "dry" systems because the a

NOx scrubber installations employing Bionomic Industries` BIONOxSOLVER have proven to be simpler, safer and considerably more cost effective than systems using sodium sulfide or hydrosulfide scrubbing reagents. Sodium sulfide and hydrosulfide are DOT libeled hazardous compounds that require dealing with major worker safety issues. They are extremely corrosive, causing difficulties in safe handling and requiring full worker personal protection. Special elaborate procedures must be put in place