- Home
- Equipment
Refine by
Emio Environmental Equipment & Supplies
11 equipment items found
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
The EMIOTEST 3114 automatic dust meter, featuring an innovative technical solution, is a portable device designed to perform periodic measurements of dust concentration in gases (e.g., exhaust gases) in closed ducts and determine dust mass flow, e.g., dust emissions into the air. The measurement is based on the isokinetic sampling of a partial stream of the tested gas and the separation of solid ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
This is a new solution in a series of devices manufactured at EMIO, designed to measure gas volume flow in closed channels. Similar to the DFM 1194/1197 flowmeters, the DFM 2006 flowmeter operates on the principle of micromanometric differential pressure ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
The "S" type aspiration velocity probes in the EMIOTEST 3114 and EMIOTEST 2598 dust meter kits enable isokinetic sampling of dust from the waste gas stream from technological processes or technical operations in order to determine the concentration and mass flow of ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
Set of devices for collecting gas samples with an aspirated side ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
The segmented, unheated "S" type aspiration velocity probes in the EMIOTEST 3114 dust meter kit allow for sampling dust from the exhaust gas stream from technological processes or technical operations to determine the dust concentration and mass flow rate. The probe consists of a selected probe head connected to the selected segment(s) and a connected aspiration and impulse path distributor. The ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
The flow rate controller is designed to check the correctness of the flow rate indication by the EMIOTEST 2598 and EMIOTEST 3114 dust ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
Damping tubes are designed to measure gas velocity in closed channels. They are manufactured in one-piece or segmented versions for connection to a screw-on head. The segments are used to assemble damping tubes of the required length. The segments can be made entirely of stainless steel. Each segment is terminated in a way that allows connection to the next segment or ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
EMIO Innovation and Implementation Company offers a dust separator made of stainless steel or titanium. Designed for internal filtration, the separator allows the use of flat or tube-shaped filter ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
CMWT-2007 digital meter is designed for direct measurement of relative humidity and temperature of the gas in ducts, under conditions without presence of condensate and soot. The device allows the registration and calculation of gas humidity degree X and carries out measurement reports. Data can be also transfered to ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
The set of devices marked as ZPPW is an additional accessory of the EMIOTEST 3114 dust meter, intended for collecting a representative sample of dust from dust-gas ducts characterized by a high concentration of dust in the gases using the gravimetric ...
Manufactured by:EMIO Innovation and Implementation Company Sp. z o. o. based inWroclaw (Lower Silesia), POLAND
The LSSE-2 is designed for users to periodically verify the correct operation of EMIO's EMIOTEST series gravimetric dust meters and DFM series flow meters. These checks are intended to verify compliance with the quality system requirements set for accredited testing laboratories by the PN-EN ISO/IEC 17025:2018 standard. Performing these checks ensures the device remains fully operational and ...